EdgeTX User Manual
v2.11
v2.11
  • EdgeTX User Manual v2.11
  • Summary of changes since v2.10
  • Installing and Updating EdgeTX
    • Migrate from OpenTX to EdgeTX using EdgeTX Buddy
    • Migrate from OpenTX to EdgeTX using the Bootloader
    • Update from an earlier version of EdgeTX using EdgeTX Buddy
    • Update from an earlier version of EdgeTX using the Bootloader
    • Having trouble updating?
  • User Manual for Color Screen Radios
    • User Interface
      • Virtual Keyboards
      • Trim Navigation
    • Manage Models
    • Channel Monitor
    • Model Settings
      • Model Setup
        • Internal / External RF
        • Trainer
        • Timer 1/2/3
        • Pre-start Checks
        • Trims
        • Throttle
        • Enabled Features
        • USB Joystick
        • Customizable Switches
        • Other
      • Heli Setup
      • Flight Modes
      • Inputs, Mixes & Outputs
        • Inputs
        • Mixes
        • Outputs
      • Curves
      • Global Variables
      • Logical Switches
      • Special Functions
      • Custom Scripts
      • Telemetry
        • Sensor Configuration Options
        • Common Telemetry Sensors
    • Radio Settings
      • Tools
      • SD Card
      • Radio Setup
        • Additional Radio settings
      • Themes
      • Global Functions
      • Trainer
      • Hardware
      • Version
    • Screen Settings
      • Widgets
    • Reset Telemetry
    • Statistics
  • User Manual for Monochrome Screen Radios
    • User Inteface
    • Main View
      • Reset
      • Statistics
    • Model Settings
      • Setup
      • Heli Setup
      • Flight / Drive Modes
      • Inputs, Mixes & Outputs
        • Inputs
        • Mixes
        • Outputs
      • Curves
      • Logical Switches
      • Special Functions
      • Telemetry
        • Sensor Configuration
        • Common Telemetry Sensors
      • Display
    • Radio Settings
      • SD Card
      • Radio Setup
      • Global Functions
      • Trainer
      • Hardware
      • Version
  • Translated User Manuals
  • EdgeTX: How-To
    • Access DFU and Bootloader Mode
    • Contribute to the User Manual
    • Set-up wireless trainer with a Multi -protocol module
    • Use Bluetooth with EdgeTX
    • Configure Advanced Joystick with EdgeTX
    • Joystick Mapping Information for Game Developers
    • Disable Touchscreen
    • Use Trims to Adjust Global Variables
    • Configure a low battery alert
  • More
    • Additional Resources
    • Contributors
Powered by GitBook
On this page
Export as PDF
  1. User Manual for Color Screen Radios
  2. Model Settings
  3. Inputs, Mixes & Outputs

Outputs

PreviousMixesNextCurves

Last updated 3 days ago

The Outputs screen of Model Settings is where final adjustments to the control data are made (including subtrims, curves, endpoint, and center values) before finally sending the control data to the RF module. This is where the channel center, limits (to prevent servo binding) and output direction are set.

A Trim is a temporary adjustment to a flight control normally done while in operation with a trim switch. A Subtrim is a semi-permanant adjustment to a flight control that is normally configured when setting up the model in the output settings.

The output screen shows all the configured output channels. For each output line, it displays the values for the minimum and maximum limits, subtrim, center point, subtrim mode and channel monitor. The two options below are also available on the output page:

  • Add all Trims to Subtrims - When selected, adds the current trim value to the subtrim value for each configured output. The trim value is then reset to zero.

  • Extended Limits - When enabled, it increases the minimum and maximum range for the output values to -150 and 150. Extended limits are necessary if the full range of the control surface cannot be reached with standard limits.

Selecting an output line will give you the following options:

  • Edit - Opens the output configuration screen.

  • Reset - Sets the subtrim value back to zero. The trim value is not changed.

  • Copy Sticks to Subtrim - Adds the current value of the stick deflection as the subtrim value.

  • Copy Trims to Subtrim - Adds the current trim value to the subtrim value. The trim value is not changed.

The output configuration screen has the following configuration options:

  • Name - Name for the Output up to 6 characters.

  • Subtrim - The subtrim value (max 100). It can also be set to a global variable by pressing the "GV" button and then selecting the desire global variable from the dropdown menu.

  • Min - Minimum output limit. Commonly used to prevent servo binding on models that use servos for the control surfaces. This line will be shown in bold and highlighted if the input for this channel is in the lower half of the range.

  • Max - Maximum output limit. Commonly used to prevent servo binding on models that use servos for the control surfaces. This line will be shown in bold and highlighted if the input for this channel is in the upper half of the range.

  • Inverted - Select this option if you want to invert the output value.

  • PPM Center - Specify the pulse-width value for the center value of the output channel (between 1000 - 2000). Changing this will shift the entire output range, including upper and lower limits.

  • Subtrim mode - Defines how the subtrim value affects the min/max output values. There are two options:

    • Center Only - Only the center value shifts and the upper and lower limits do not change. The reaction of the stick differs between the upper half and the lower half from midpoint.

    • Symmetrical - the upper and lower limits will shift according to the shift of the center value. The reaction of the stick is the same on both sides of the midpoint.

Curve - Specify the custom curve (in any) that you want to use for this output. See for more information about custom defined curves.

Curves
Outputs screen
Outputs Configuration page