EdgeTX User Manual
v2.11
v2.11
  • EdgeTX User Manual v2.11
  • Summary of changes since v2.10
  • Installing and Updating EdgeTX
    • Migrate from OpenTX to EdgeTX using EdgeTX Buddy
    • Migrate from OpenTX to EdgeTX using the Bootloader
    • Update from an earlier version of EdgeTX using EdgeTX Buddy
    • Update from an earlier version of EdgeTX using the Bootloader
    • Having trouble updating?
  • User Manual for Color Screen Radios
    • User Interface
      • Virtual Keyboards
      • Trim Navigation
    • Manage Models
    • Channel Monitor
    • Model Settings
      • Model Setup
        • Internal / External RF
        • Trainer
        • Timer 1/2/3
        • Pre-start Checks
        • Trims
        • Throttle
        • Enabled Features
        • USB Joystick
        • Customizable Switches
        • Other
      • Heli Setup
      • Flight Modes
      • Inputs, Mixes & Outputs
        • Inputs
        • Mixes
        • Outputs
      • Curves
      • Global Variables
      • Logical Switches
      • Special Functions
      • Custom Scripts
      • Telemetry
        • Sensor Configuration Options
        • Common Telemetry Sensors
    • Radio Settings
      • Tools
      • SD Card
      • Radio Setup
        • Additional Radio settings
      • Themes
      • Global Functions
      • Trainer
      • Hardware
      • Version
    • Screen Settings
      • Widgets
    • Reset Telemetry
    • Statistics
  • User Manual for Monochrome Screen Radios
    • User Inteface
    • Main View
      • Reset
      • Statistics
    • Model Settings
      • Setup
      • Heli Setup
      • Flight / Drive Modes
      • Inputs, Mixes & Outputs
        • Inputs
        • Mixes
        • Outputs
      • Curves
      • Logical Switches
      • Special Functions
      • Telemetry
        • Sensor Configuration
        • Common Telemetry Sensors
      • Display
    • Radio Settings
      • SD Card
      • Radio Setup
      • Global Functions
      • Trainer
      • Hardware
      • Version
  • Translated User Manuals
  • EdgeTX: How-To
    • Access DFU and Bootloader Mode
    • Contribute to the User Manual
    • Set-up wireless trainer with a Multi -protocol module
    • Use Bluetooth with EdgeTX
    • Configure Advanced Joystick with EdgeTX
    • Joystick Mapping Information for Game Developers
    • Disable Touchscreen
    • Use Trims to Adjust Global Variables
    • Configure a low battery alert
  • More
    • Additional Resources
    • Contributors
Powered by GitBook
On this page
Export as PDF
  1. User Manual for Monochrome Screen Radios
  2. Model Settings
  3. Telemetry

Common Telemetry Sensors

The following sensors are commonly used and normal automatically detected by EdgeTX:

Name
Description
Data source

1RSS

Received signal strength antenna 1 (RSSI)

Receiver

2RSS

Received signal strength antenna 2 (RSSI)

Receiver

Rqly

Receiver link quality (valid packets)

Receiver

RSNR

Receiver signal-to-noise ratio

Receiver

RFMD

Receiver packet rate

Receiver

TPWR

Transmitter transmitting power

Transmitter

TRSS

Transmitter signal strength antenna

Transmitter

TQly

Transmitter link quality (valid packets)

Transmitter

TSNR

Transmitter signal-to-noise ratio

Transmitter

ANT

Sensor for debugging only

Transmitter

GPS

GPS Coordinates

GPS / Flight Controller

Alt

GPS Altitudes

GPS / Flight Controller

Sats

GPS Satellites acquired

GPS / Flight Controller

Hdg

Magnetic orientation

GPS / Flight Controller

RXBt

Battery voltage

Flight Controller

Curr

Current draw

Flight Controller

Capa

Current consumption

Flight Controller

Ptch

FC Pitch angle

Flight Controller

Roll

FC Roll angle

Flight Controller

Yaw

FC Yaw angle

Flight Controller

FM

Flight mode

Flight Controller

VSPD

Vertical Speed

Flight Controller w/ Baro

PreviousSensor ConfigurationNextDisplay

Each sensor has two auto generated sensors for their minimum and maximum values. They share the same name with a negative and positive symbol added to the end. For example: RXBt + This dispalys the maximum value that the sensor attained during the flight. Using the or Flight function will reset this value to 0.

Reset Telemetry