Setup

The Setup screen is where you start to configure your model. It contains the following settings:

Name - Name of the model. The maximum number of characters is 10.

  • To edit the text, using the [roller] or [dial], press the button, scroll to select the desired letter, then press the button again to move to the next space. To toggle between lower and upper case, long-press the button. Press the [RTN] button to exit out of text editing mode.

Image - Image displayed on the main view (only for radios with 212 x 64 displays).

Image dimensions shall be 64 x 32 pixels, 16 bit, grayscale, .bmp file. The image must be stored in the IMAGES folder of the SD card.

Timer 1/2/3 - There are 3 configurable timers in EdgeTX. They all have the same options:

Timer 1 [Mode] [Switch]

[Mode]: The options include:

  • OFF- The timer is not used

  • ON - The timer runs all the time

  • Start -The timer starts once the configured switch is activated. After the time is started, the timer ignores the switch position.

  • THs (Throttle) - The timer starts once the throttle is raised and the configured switch is activated. The timer will stop counting if either the throttle position is lowered back to the minimum value or the configured switch is deactivated.

  • TH% (Throttle %) - The timer counts proportionally to the throttle. It counts in real-time at full throttle and half speed at 50% throttle.

  • THt (Throttle Start) - The timer starts once the throttle is raised and the configured switch is activated. After starting, the timer ignores the throttle position and will keep counting unless the switch is deactivated.

[Switch]- Select the switch that will trigger the timer to start. If no switch is selected, the timer will trigger based only on the configured mode. In addition to a switch, you can also select a trim, a telemetry source (triggered when telemetry data is received from that source), or physical activity (stick movement or button press) (labeled as ACT)

Those items with a "!" mark in front of the trigger name mean that the condition is reversed. For example, "!SA-" means "when SA switch is not in middle/center position (= up or down)".

Name: Name of the timer

Start- The time used for the timer's advanced functions. The default value is 00:00 and when left as such, the timer operates like a stopwatch, counting upward until stopped. If a different time is entered in this box, then the additional field will appear next to the time with the options: Remain or Elaps.

If set to Remain, the counter will function like a countdown timer - counting down from the designated time to zero and then alerting the user. If set to Elaps, the timer functions like an alarm, counting up from zero until the designated time and then alerting the user.

Persist (Persistence):

  • Off - The timer value is reset when switching models or when the radio is turned off / on.

  • Flight - The timer value is NOT reset when switching models or when the radio is turned off / on. The timer value is only reset when the Reset flight option is selected in the Reset menu.

  • Manual Reset - The timer value is reset only when it is individually selected to be reset (example: Reset timer1) in the Reset menu.

Minute (Minute Call) - If selected, you will be notified every minute that passes as described in the Count Down option.

Count Down:

  • Silent - No notification is given until the timer reaches zero. When it reaches zero, you will hear one beep.

  • Beeps - The radio will beep every second starting at the time designated.

  • Voice - The radio will count down by second starting at the time designated.

  • Haptic -The radio will vibrate every second starting at the time designated.

Function Switches

Function Switches

The functions switches are a type of multiposition switch (on select transmitters) that are managed directly by EdgeTX. Physically, they look like a regular 6-pos switch but are much more flexible.

Unlike other switches managed at the radio level, function switches are defined per model and configured in the model setup page. They contain the following configuration options:

Switch Type

  • None: the switch is disabled

  • Toggle : they are active only during the push duration

  • 2POS: pushing the switch will alternate the state between OFF and On

Switch group

A traditional 6POS is a group of 6 switches that work together, where only one can be active at a time. Function switches expand that concept and let you choose how the switches should be grouped.

'-' defines a function switch with no group. Pushing it will only affect this switch.

'1', '2' or '3' define groups. All the switches in a group act together, where only one (the last pushed) can be active.

Always on groups

Selecting this check box makes the assigned group act like a traditional 6-position switch where one button from the group must be on at all times.

Startup Position

Start - Defines the state that each switch will be in when the model is loaded.

  • Switch is inactive

  • Switch is active

  • = Switch is set to the same state it was in when the model was last used (it keeps old state).

Unlike hardware 6-POS implementation (Horus, TX16S,...), software managed switches can not be used as an analog source, they are individual switches with either ↑ or ↓ position. The behavior of previous 6P source can be achieved using a combination of mixer lines

Trims settings

E.Limits (Extended Limits) - When enabled, it increases the minimum and maximum range for the output values to -150 and 150. Extended limits are necessary if the full range of the control surface cannot be reached with standard limits.

E. Trims) Extended Trims: Increases the maximum trim adjustment value from ±25% to ±100%.

Reset - This resets all trim values to zero.

Show trims: When set to Yes, it will display the numerical trim value on the trim bar. When set to CHANGE, it will display the numerical value once the trim is no longer at zero.

Trim Step: Defines the amount of increase/decrease in trim when the trim switch is pressed.

  • Course = 1.6%

  • Medium = 0.8%

  • Fine = 0.4%

  • Extra Fine = 0.2%

  • Exponential = 0.2% near the center and the step value increases exponentially as the distance from the center increases.

Throttle Settings

T-Reverse: When enabled, this option reverses the output direction of the configured throttle channel.

T-Source: The source that will be used for the throttle.

T-Trim-Idle: When enabled, the throttle trim will only affect the bottom portion of the throttle band.

For example, with Trim idle only enabled, the throttle stick at the lowest point might have a value of -80 and the center point will still be 0 and the highest point of 100. Without this enabled, the throttle stick at the lowest point might have a value of -80 however, the center point will be 20 and the highest point of 100.

T-Trim-SW: The trim switch that will be used to trim the throttle. It is possible to substitute the throttle trim switch with the aileron, rudder, or elevator trim switches.

Preflight Checks options

Preflight Checks

Whenever a new model is loaded, EdgeTX will conduct pre-flight checks based on the checks that are configured on this page. If any of the checks are failed, EdgeTX will give the user an audio and visual warning that must be acknowledged before using the model. The following preflight checks are configurable:

Checklist - When this option is selected, the model notes file will be displayed when the model is loaded. A valid model notes file must be in the Models folder on the SD card. The model notes file must be a .txt file and must have the EXACT same name as the model it is for, for example: Mobula6.txt. The text in the file is up to the user.

T-Warning - When selected, the radio will check that the throttle is at the minimum value for the configured throttle source in the T-Source configuration option.

Cust-Pos - When this option is selected, the value designated in POS.% will be used for the T.Warning.

Pos.% - minimum value of the throttle for the throttle warning when Cust-Pos is enabled.

S-Warning - The section displays all the switches that are configured on the radio and allows you to select which position is the correct position for the switch state check. Selecting the switch will cycle through the available switch positions or turn the check off for the switch completely.

Pot warn- When activated, this option checks the position of the pots & sliders. There are three options - OFF, ON and AUTO. When ON or AUTO is selected, buttons for the available pots and sliders will appear. To enable the Pot warning for an individual Pot, select the pot with the [roller] or [dial] and click the button to highlight it. Highlighted pots are enabled.

  • OFF - Pot and slider positions are not checked.

  • Manual - Positions are checked against manually configured pot and slider positions. To manually set the check position, select manual the from menu, select the item that you want to set, and long-press the [Enter] button to set its current position for the check.

  • AUTO - Positions are checked for pots and sliders and compared to the last automatically saved position before the radio was turned off or the model was changed.

Ctr Beep - Allows you to turn on/off the center beep function for the individual sticks, pots, and sliders by highlighting them with the [roller] or [dial] and pressing the button. When a switch is highlighted, the function is enabled.

Glob. Funs - When enabled, global functions programmed in the radio settings will apply to this model. When disabled, global functions will not apply to this model.

Global functions are special functions that are applied across all models. Refer to Special Functions for information on configurable settings.

ADC Filter - Enables/disables the ADC filter for this model. The global option will take the value designated in the radio settings, which is on by default.

The ADC filter is a filter for the proportional channels (sticks, pots, sliders), smoothing out smaller fast movements that occur due to noise in the system electronics. Normally, this filter should be disabled for models with flight controllers.

Internal / External RF

The configuration settings for both the Internal and External RF sections work the same. The only difference is that the Internal RF section is for configuring the built-in module and the External RF section is for configuring an RF module in the external module bay.

The configuration options are: off or the module name of the installed module as configured in the Radio settings. Configuration options are unique to each installed module. Please consult the manufacturer's documentation for configuration options.

Configuration options for the multi-protocol module are described here: https://www.multi-module.org/using-the-module/protocol-options

Receiver number - A receiver number is a user-assigned number for a model that is sent to the receiver when bound. Each model must have a unique receiver number. However, models using different protocols may have the same receiver number without issues. EdgeTX will inform you when a receiver number is unique or if it is already being used with a text above the number field.

If using the radio in gamepad mode, both internal and external RF modules should be turned off. This will result in increased performance when connected to a computer via USB.

Trainer Mode - The Trainer Mode option is where you can configure the CPPM passthrough mode and method. When enabled, this allows the CPPM signals from a radio in Slave mode to be passed through to another radio in Master mode which will then pass the signal to the model it is connected to. CPPM passthrough can be used for several different use cases, such as: connecting a head tracker, Instructor / Student training mode, and controlling complex models that require more stick inputs than available on a standard transmitter.

Master mode - This is the mode for the radio that will be connected to the model. This radio also shall configure the special/global function (Trainer) to activate the passthrough mode. When the passthrough mode is activated, the CPPM signals from the radio in Slave mode will be sent to the model for control.

Slave mode - This is the mode for the radio that will pass it's CPPM values to the radio in Master mode, which are then sent to the model.

Below are the possibile configuration options:

  • Off - Trainer mode is not used for this model.

  • Master / Jack - Master mode using a cable connection.

  • Slave / Jack - Slave mode using a cable connection.

    • Channel Range - This is the range of channels that will be sent to the radio in Master mode. Channel 10 is the recommended last channel to use.

    • PPM Frame - The first field is the length of the PPM frame. The second field is the stop length/delay between pulses. The dropdown is to select the polarity of the signal. Note: In most cases, the default setting does not need to be changed.

  • Master / Bluetooth - Master mode using a Bluetooth connection (if installed in radio).

  • Slave / Bluetooth - Slave mode using a Bluetooth connection (if installed in radio).

  • Master / Multi - Master mode using an additional externally mounted Multi-protocol module for the connection. For more information on this setup, see

Set-up wireless trainer with MPMsee Set-up wireless trainer with MPM

Pressing the [PAGE>] button will take you to the Heli Setup screen.

Last updated