EdgeTX supports the following color screen radios:

• FlySky NV14 / EL18

• FrSky X10 / X10S / X10 Express / X10S Express

• FrSky X12S / X12S-IRSM

• Jumper T16 / T16 Plus / T16 Pro Hall

• Jumper T18 / T18 Lite / T18 Pro

• RadioMaster/Eachine TX16S / RadioMaster TX16S MAX / RadioMaster TX16S Mark II

The select model screen allows you to create new models, select which model is active, create and apply model labels, and create model templates.

Selecting & managing existing models

The active model's name will be highlighted (yellow in this case) and displayed on the screen's top bar. Double-tapping an active model will give you the following options:

• Duplicate model - This option creates an exact duplicate of the model with the same name. Changes to the model name or other settings need to be made in the Model Settings tab.

• Edit Labels - When this option is selected, all configured labels will be displayed and can be selected for this model. More Information about Model Labels is below.

• Save as template - this option saves a copy of the model as a model template.

Double-tapping on a non-active model (unhighlighted) will give you the following options:

• Select model - this option selects this model as the active model.

• Duplicate model - same as described above.

• Delete model - this option moves the model to the deleted folder on the SD Card. Only models that are not active can be deleted.

• Edit Labels - same as described above.

• Save as template - same as described above.

Creating a new model

To create a new model, select the New Model button in the upper right corner. You will then be presented with the following options:

• Blank Model - This will create a blank model with only the default options configured.

• PERSONAL - This option will allow you to select one of your saved model templates and then create a copy of it as a new model.

• SoarETX - This will display pre-configured model templates for radio-controlled model sailplanes.

• WIZARD - This will launch the new model wizard and create the model as configured in the wizard.

Model Labels

Model labels allow you to give each model one or more labels. You are then able to filter the models displayed in the Model Select screen based on the labels that you select. This allows people with many configured models to find them easier. By default, the Favorites and Unlabeled labels are created automatically. All models are considered unlabeled until a label is applied to them.

Filtering models using labels

To filter the visible models based on their labels, select the filter or filters from the left column. It will automatically filter out the models that do not have those model labels.

Assigning labels to models

To assign a label to a model, double-tap on the model or press [Enter] when the model is selected and then select Edit Labels. Once selected, all configured labels will be displayed and one or more labels can be selected for this model. Labels applied to the model will be designated with a check icon.

Creating new model labels

To create a new model label, select the New button on the bottom left of the screen. The Enter Label pop-up will appear and you can enter the desired label name. Select Save to save the new label.

Editing model labels

Long press [Enter] or long tap on desired label and you be shown a menu with the following options:

• Rename Label - change the label's name

• Delete Label - Deletes the label from the label list and from all models that have it assigned.

• Move Up - positions the label higher on the list

• Move Down - - positions the label lower on the list

Sorting Models

The icons below the label list are for sorting the filtered models. Models can be sorted either alphabetically or by the last time they were selected as described in the image below.

The model setup page is the default page for model settings and is where you start to configure your model. It contains the following settings:

Model name

Enter the desired name for the model. The maximum number of characters is 15.

Labels

Here you may assign a label from your defined label list. By default, the model label will be Unlabeled. More information on creating labels can be found on the Select Model page.

Model image

When the folder icon is selected, a window will pop up allowing you to select an image file from the images folder on your SD Card.

Use global functions

When enabled, global functions programmed in the radio settings will apply to this model. When disabled, global functions will not apply to this model.

ADC Filter

Enables/disables the ADC filter for this model. The global option will take the value designated in the radio settings, which is on by default.

The Model Settings screen contains all the options to configure your model. Across the top of the page you will see icons that will take you to different pages of model settings when selected. The default screen for model settings is theModel Setup screen.

The icons at the top of the screen include (in order from left to right):

• Model Setup

• Heli Setup (only visible if EdgeTX is custom compiled with this option.)

• Flight modes

• Inputs

• Mixes

• Outputs

• Curves

• Global Variables

• Logical Switches

• Special Functions

• Telemetry

The user interface of EdgeTX can be navigated by physical buttons, the touch interface, or a combination of both.

Buttons:

• [SYS] - System Button - Short press [SYS] button to go to the Radio Settings page.

• [MDL] - Model Button - Short press [MDL] button to go to the Model Settings page - Long press [MDL] button to go to the Select Model page

• [RTN] - Return / Back - Short press [RTN] button to return to the previous page, previous menu or cancel action

• [PAGE>] / [PAGE<] - Page next & page previous - Used to navigate between different screens, tabs, or options settings, depending on the screen.

• [TELE] - Telemetry - Press the [TELE] button to go to the Screen Settings page

• [Roller] or [Dial] - Next & previous value The roller is used to navigate through menu options.

• [Enter] - Accept - Used to select option, function or accept value - Push [Roller] or [Dial] button to select or enter.

Touch Interface:

Certain radios are equipped with a touch screen. On these radios, you can interface with the menu options either with touch or physical buttons.

Touch the EdgeTX icon in the upper left corner of the screen to open the main navigation menu. Touch the desired menu option to select it.

Pressing the roller from the main screen will also open the main navigation menu. You can then scroll using the roller to the desired menu option and select it by pressing the roller.

The Trainer screen is where you can configure the CPPM passthrough mode and method. When enabled, this allows the CPPM signals from a radio in Slave mode to be passed through to another radio in Master mode which will then pass the signal to the model it is connected to. CPPM passthrough can be used for several different use cases, such as: connecting a head tracker, Instructor / Student training mode, and controlling complex models that require more stick inputs than available on a standard transmitter.

Master mode - This is the mode for the radio that will be connected to the model. This radio also shall configure the special/global function (Trainer) to activate the passthrough mode. When the passthrough mode is activated, the CPPM signals from the radio in Slave mode will be sent to the model for control.

Slave mode - This is the mode for the radio that will pass it's CPPM values to the radio in Master mode, which are then sent to the model.

Below are the possibile configuration options:

• Off - Trainer mode is not used for this model.

• Master / Jack - Master mode using a cable connection.

• Slave / Jack - Slave mode using a cable connection.

  • Channel Range - This is the range of channels that will be sent to the radio in Master mode. Channel 10 is the recommended last channel to use.

  • PPM Frame - The first field is the length of the PPM frame. The second field is the stop length/delay between pulses. The dropdown is to select the polarity of the signal. Note: In most cases, the default setting does not need to be changed.

• Master / Bluetooth - Master mode using a Bluetooth connection (if installed in radio).

• Slave / Bluetooth - Slave mode using a Bluetooth connection (if installed in radio).

• Master / Multi - Master mode using an additional externally mounted Multi-protocol module for the connection. For more information on this setup, see Set-up wireless trainer with MPM

EdgeTX provides 3 timers that can be custom programmed. Below are the configuration options.

Name: Name of the timer

Mode:

• OFF- The timer is not used

• ON - The timer runs all the time

• Start -The timer starts once the configured switch is activated. After the time is started, the timer ignores the switch position.

• Throttle - The timer starts once the throttle is raised and the configured switch is activated. The timer will stop counting if either the throttle position is lowered back to the minimum value or the configured switch is deactivated.

• Throttle % - The timer counts proportionally to the throttle. It counts in real time at full throttle and at half speed at 50% throttle.

• Throttle Start - The timer starts once the throttle is raised and the configured switch is activated. After starting, the timer ignores the throttle position and will keep counting unless the switch is deactivated.

Switch- Select the switch that will trigger the timer to start. If no switch is selected, the timer will trigger based only on the configured mode. In addition to a switch, you can also select a trim, a telemetry source (triggered when telemetry data is received from that source), or physical activity (stick movement or button press) (labeled as ACT)

Start- The time used for the timer's advanced functions. The default value is 00:00 and when left as such, the timer operates like a stopwatch, counting upward until stopped. If a different time is entered in this box, then the additional Direction drop-down menu option will appear.

Direction - If set to Show Remaining, the counter will function like a countdown timer - counting down from the designated time to zero and then alerting the user. If set to Show Elapsed, the timer functions like an alarm, counting up from zero until the designated time and then alerting the user.

Minute Call - If selected, you will be notified every minute that passes as described in the Count Down option.

Count Down:

• Silent - No notification is given until the timer reaches zero. When it reaches zero, you will hear one beep.

• Beeps - The radio will beep every second starting at the time designated.

• Voice - The radio will count down by second starting at the time designated.

• Haptic -The radio will vibrate every second starting at the time designated.

Persistent:

• Off - The timer value is reset when switching models or when the radio is turned off / on.

• Flight - The timer value is NOT reset when switching models or when radio is turned off / on. The timer value is only reset when the Reset flight option is selected in the Reset telemetry menu.

• Manual Reset - The timer value is reset only when it is individually selected to be reset (example: Reset timer1) in the Reset telemetry menu.

EdgeTX has to possibility to select a specific source and trim for the model throttle and allows for the following configuration options:

Reverse: When enabled, this option reverses the output direction of the configured throttle channel.

Source: The source that will be used for the throttle.

Trim idle only: When enabled, the throttle trim will only affect the bottom portion of the throttle band.

Trim switch: The trim switch that will be used to trim the throttle. It is possible to substitute the throttle trim switch with the aileron, rudder, or elevator trim switches.

Whenever a new model is loaded, EdgeTX will conduct pre-flight checks based on the checks that are configured on this page. If any of the checks are failed, EdgeTX will give the user an audio and visual warning that must be acknowledged before using the model. The following preflight checks are configurable:

Display checklist - When this option is selected, the model notes file will be displayed when the model is loaded. A valid model notes file must be in the Models folder on the SD card. The model notes file must be a .txt file and must have the EXACT same name as the model it is for, for example: Mobula6.txt. The text in the file is up to the user.

Throttle state - When selected, the radio will check that the throttle is at the minimum range value for the configured throttle source in the Throttle menu.

Custom Position? - When this option is selected, a number box will be shown that can be configured with a user-defined value for the throttle state check.

Switches - The section displays all the switches that are configured on the radio and allows you to select which position is the correct position for the switch state check. Selecting the switch will cycle through the available switch positions or turn the check off for the switch completely. Yellow switches have the switch position check activated. White switches e de-activated.

Pots & Sliders- When activated, this option checks the position of the pots & sliders. There are three options - OFF, ON and AUTO. When ON or AUTO is selected from the drop-down menu, buttons for the available pots and sliders will appear.

• OFF - Pot and slider positions are not checked.

• ON - Positions are checked against manually configured pot and slider positions that are set to active (yellow). To manually set the check position, select ON from the drop-down menu, put the pots and sliders into the desired position, and activate them by selecting them (yellow).

• AUTO - Positions are checked for activated pots and sliders and compared to the last automatically saved position before the radio was turned off or the model was changed.

Center Beep - Allows you to turn on / off the center beep function for the individual sticks, pots, and sliders by selecting them (yellow).

The configuration settings for both the Internal and External RF pages work the same. The only difference is that the Internal RF section is for configuring the built-in module and the External RF section is for configuring an RF module in the external module bay.

The Internal / External RF modules are "active" for a model when the buttons are yellow and inactive when they are white.

The configuration options are: off or the module name of the installed module as configured in the hardware section of the Radio settings. Configuration options are unique to each installed module. Please consult the manufacturer's documentation for configuration options.

Receiver number

The receiver number is a user-assigned number for a model that is sent to the receiver when bound. Each model must have a unique receiver number. However, models using different protocols may have the same receiver number without issues. EdgeTX will inform you when a receiver number is unique or if it is already being used with a text above the number field.

Trims are used adjust the center position of a given stick axis. EdgeTX has the following time configuration options:

Reset - This resets all trim values to zero.

Trim Step: Defines the amount of increase/decrease in trim when the trim switch is pressed.

• Course = 1.6%

• Medium = 0.8%

• Fine = 0.4%

• Extra Fine = 0.2%

• Exponential = 0.2% near the center and the step value increases exponentially as the distance from the center increases.

Extended Trims: Increases the maximum trim adjustment value from ±25% to ±100%.

Display trims: When set to ON, it will display the numerical trim value on the trim bar. When set to CHANGE, it will display the numerical value once the trim is no longer at zero.

The Inputs screen of Model Settings is where you map your physical radio controls (for example: sticks, sliders, and pots) to a software input to be used by the radio. After the control has been mapped it is then possible to apply modifiers to the inputs such as a weight, offset or curve which will then be applied anywhere that input is used. Although it is possible to also assign switches as inputs, it is normally not needed as switch outputs seldomly need to be modified by a weight, offset or curve. By default, EdgeTX will automatically map your contoller sticks to Aileron, Elevator, Throttle, Rudder based on the default channel order defined in Radio Setup.

Selecting the + button will create a new input and open the input configuration page. Selecting an existing input will give you the following options:

• Edit - opens the input configuration page for that input line.

• Insert before - Inserts a new input line before the selected input.

• Insert after- Inserts a new input line after the selected input.

• Copy - copies the selected input line.

• Move - selects the input line to be moved. The input is moved using one of the paste commands after a new line is selected (i.e. cut & paste).

• Delete - deletes the selected input line.

• Paste before - pastes the copied or moved input line before the selected input line.

• Paste after - pastes the copied or moved input line before the selected input line.

Input configuration page

The input configuration page allows you to edit the input configuation parameters. To the right of the configuration parameters, you can see a live graph that shows how your configuration options will affect the slope of the input.

• Input Name - Name for the input. Four character are possible.

• Line Name - Name of the individual line in the input. Multiple physical inputs can be mapped to one input by adding an additional input line under the input.

• Source - The physical control used for the input. In addition to physical controls, you can also specify MAX (always returns 100), cyclics, trim switches, channel values and more. Moving the physical control after the source has been selected will automatically map it to that input.

• Weight - Percentage value of the stick travel to use (often referred to as "rates").

• Offset - The value added to or subtracted from the input source.

• Switch - The switch that activates the input line. If no switches are defined then it is always active.

• Curve - Specifies the type of curve that will be used. The following curve options exist:

  • Diff - Multiplies only the range above or below the middle (0) by the specified %.

  • Expo -The input value is changed exponentially. Increasing the % will result with a gentle slope near the middle(0). Decreasing the % will result in a steep slope near the middle (0). With a % of 0, the slope will be linear.

  • Func -
  • Cstm - assigns a custom defined curve. See Curves for more information about custom defined curves.

When selecting the gear button at the bottom of the screen, the following option window will be displayed.

Side - Specifies the input range for which this line setting is valid. If you select ---, it will be valid in the entire range of Source values. If you select x>0, it will be valid in the upper half of the value of Source. If you select x<0, it will be valid in the lower half of the value of Source.

Trim - Specifies whether or not to include the trim values in this input. Additionally, you can select a different trim to use for this input.

Modes - Specifies which flight modes this input is active for.

Flight modes allow you to have different trim settings for each flight mode. Once multiple flight modes are configured, you can adjust the trim settings in each flight mode without affecting the trim settings in other flight modes (unless they are configured to do so). There are 9 possible flight modes to use, with Flight Mode 0 being the default flight mode.

The Flight Mode screen displays buttons for each flight mode. Flight mode buttons in yellow designate the current active flight mode. Selecting a flight mode button will take you to the configuration page for that flight mode.

Check FM Trims: When the check FM trims button is pressed, the trims for the current flight mode are temporarily disabled. This is used to test the impact of the current flight mode’s trims on the outputs.

The flight mode conifiguration screen has the following options:

Name: The custom name for the flight mode. If configured, this name will be shown on the lower center position of the main screen between the trims.

Switch: The trigger to enable that flight mode. It can be a switch, pot, telemetry, trim or logical switch.

Fade in: Gradually change the trim value when this flight mode is enabled. Specify the time in seconds (0.0 - 25.0) until the value change is completed.

Fade out: Gradually change the trim value when this flight mode is disabled. Specify the time in seconds (0.0 - 25.0) until the value change is completed.

Trims: Once the Setup button is selected, the trim setup screen will be shown.

To configure the trims, select the trim that you want to configure to make sure that it is turned on (yellow). Then select the flight mode (0-8) that will provide the initial trim value and modifier (= or +) from the drop-down menu.

Modifier - there are two possible value modifiers = and +. The = modifier uses the trim value directly from the selected flight mode. The + modifier uses the trim value from the selected flight mode and then adds the trim value from the flight mode you are configuring.

Example 1: If you are configuring FM1 and set the value to =0, FM1 will have the trim value of the current value of the same trim in FM0. In this case, changes made to the trim in FM1 will also affect the trim in FM0 and vice-versa.

Example 2: If you are configuring FM1 and set the value to +0, FM1 will have the trim value of the same trim in FM0, plus any trim changes made while in FM1, In this case, changes made to the trim in FM1 do not affect the trim in FM0. However, changes to trim values FM0 will affect trim values in FM1.

The Mixes screen of Model Settings is where several Inputs can be combined into one "Channel Mix". These mixes are then assigned to a radio channel for output. This is also the place where switches, knobs or sliders are assigned to a channel for output. Similar to the Input section, it is also possible to assign a weight, offset or curve to a channel mix.

Selecting the + button will create a new mix and open the mixes configuration page. Selecting an existing mix will give you the following options:

• Edit - opens the mixes configuration page for that mix line.

• Insert before - Inserts a new mix line before the selected mix.

• Insert after - Inserts a new mix line after the selected mix.

• Copy - copies the selected mix line.

• Move - selects the mix line to be moved; mix is moved using one of the paste commands after a new line is selected (i.e. cut & paste).

• Delete - deletes the selected mix line.

• Paste before - pastes the copied or moved mix line before the selected mix line.

• Paste after - pastes the copied or moved mix line before the selected mix line.

Show mixer monitors - Selecting this option will display a bar graph on the mix channels showing the current value for that mix channel.

The upper right portion of the mixes configuration page contains a channel monitor for the selected mix line. It shows the output (top) and mix (bottom) values. The following configuration options are also available:

• Name - Name of the mix (optional). Up to 6 characters are allowed.

• Source - The source for the mix. In addition to inputs, you can select sticks, pots, sliders, trims, physical and logical switches, heli mixer outputs, trainer import channel values, and other channels.

• Weight- Percentage of the source value to use.

• Offset - The value added to or subtracted from the source.

• Switch - The physical switch that activates this mix line (optional). If no switch is selected, then the mix will be active by default.

• Curve - Specifies the type of curve that will be used. See the curve section on the Inputs page for detailed explanations of the different curve types.

• Multiplex - The multiplex setting defines how the current mixer line interacts with the others on the same channel. Add will add its output to them, Multiply will multiply the result of the lines above it, and Replace will replace anything that was done before it with its output.

• Modes - Specifies which flight modes this mix is active for.

• Trim - Specifies whether or not to include the trim values in this mix. For the trim values to be included, the trim field for the relevant input must also be enabled on INPUTS screen.

• Warning -when selected, the radio will beep when this mix is active. You can choose from OFF (0) or beep patterns 1, 2, 3.

• Delay up - Creates a time delay in seconds between when the source value increases and when it is output.

• Delay down - Creates a time delay in seconds between when the source value decreases and when it is output.

• Slow up - Adjusts the transition speed for source value increases. Specify the time to transition from -100% to + 100% in seconds. You can specify a range from 0.0 seconds to 25.0 seconds.

• Slow down - Adjusts the transition speed for source value decreases. Specify the time to transition from -100% to + 100% in seconds. You can specify a range from 0.0 seconds to 25.0 seconds.

The Heli Setup page in Model Settings is an optional page that is available on custom-compiled versions of EdgeTX. The heli setup page is often used for collective pitch mixing (CCPM) used in flybared helicopters where the receiver directly controls the swashplate servos. Most flybarless helicopters do not need to configure this page. The outputs of the CCPM mixer are CYC1, CYC2, and CYC3, which need to be assigned to an output channel on the Mixes screen.

The heli setup page has the following configuration options:

• Swash Type - Swash type for your model. Options are 120, 120x, 140, and 90.

• Swash Ring - Set the swash ring limit only as needed. 1 = maximum limit -> 100 or 0 = no limit.

• Long. cyc. source - Select source input.

• Lateral cyc.source -Select source input.

• Coll. pitch source - Select source input.

• Weight - Percentage value of the stick travel to use.

To be able to support many different types of radio transmitters, EdgeTX uses a generic control data flow that can be applied to any radio transmitter. In this data flow, any of the radio's physical controls (sticks, switches, sliders, pots) can be mapped to an input in the software. These inputs can be directly assigned or combined with other inputs into a single mix. These mixes can be modified by applying weights, offsets, and curves and are then assigned a channel for output. Final adjustments to the control data are made (including subtrims, curves, endpoint, and center values) before finally sending the control data to the RF module. The flowchart below depicts a visual summary of this control data flow. Detailed information about the flow is provided in the following sections , , and .

EdgeTX uses the icons below to designate different types of sources.

The Outputs screen of Model Settings is where final adjustments to the control data are made (including subtrims, curves, endpoint, and center values) before finally sending the control data to the RF module. This is where the channel center, limits (to prevent servo binding) and output direction are set.

The output screen shows all the configured output channels. For each output line, it displays the values for the minimum and maximum limits, subtrim, center point, subtrim mode and channel monitor. The two options below are also available on the output page:

• Add all Trims to Subtrims - When selected, adds the current trim value to the subtrim value for each configured output. The trim value is then reset to zero.

• Extended Limits - When enabled, it increases the minimum and maximum range for the output values to -150 and 150. Extended limits are necessary if the full range of the control surface cannot be reached with standard limits.

Selecting an output line will give you the following options:

• Edit - Opens the output configuration screen.

• Reset - Sets the subtrim value back to zero. The trim value is not changed.

• Copy Sticks to Subtrim - Adds the current value of the stick deflection as the subtrim value.

• Copy Trims to Subtrim - Adds the current trim value to the subtrim value. The trim value is not changed.

The output configuration screen has the following configuration options:

• Name - Name for the Output up to 6 characters.

• Subtrim - The subtrim value (max 100). It can also be set to a global variable by pressing the "GV" button and then selecting the desire global variable from the dropdown menu.

• Min - Minimum output limit. Commonly used to prevent servo binding on models that use servos for the control surfaces.

• Max - Maximum output limit. Commonly used to prevent servo binding on models that use servos for the control surfaces.

• Inverted - Select this option if you want to invert the output value.

• PPM Center - Specify the pulse-width value for the center value of the output channel (between 1000 - 2000). Changing this will shift the entire output range, including upper and lower limits.

• Subtrim mode - Defines how the subtrim value affects the min/max output values. There are two options:

  • Center Only - Only the center value shifts and the upper and lower limits do not change. The reaction of the stick differs between the upper half and the lower half from midpoint.

  • Symmetrical - the upper and lower limits will shift according to the shift of the center value. The reaction of the stick is the same on both sides of the midpoint.

The Curves screen of Model Settings allows you to define custom curves to use in the Inputs, Mixes, or Output screens. The curves screen will show all of the configured custom curves, with a graphical representation of each curve, the number of points, and the curve type.

Selecting an existing custom curve will display the following options:

• Edit - Opens the curve configuration page.

• Preset - Allows you to set the curve to one of the preset slope values (-45 to 45 degrees in 15 degree increments). The curve will have 5 points and smoothing is not enabled by default.

• Mirror - Mirrors the selected curve.

• Clear - Clears all curve values from the selected curve.

Selecting an unconfigured curve will give you the following options:

• Edit - Opens the curve configuration page.

• Preset - Allows you to set the curve to one of the preset slope values (-45 to 45 degrees in 15 degree increments). The curve will have 5 points and smoothing is not enabled by default.

Selecting Edit for a configured or unconfigured curve will open the curve configuration screen and display the following options:

• Name - Name for the curve. Only 3 characters are possible.

• Type - Type of curve: Options are Standard and Custom

  • Standard - Horizontal axis points are fixed values based on the number of points. Vertical axis points are adjustable.

  • Custom - Both horizontal and vertical axes are adjustable.

• Number of Points - number of points in the curve

• Smooth - When enabled, connects the points with curved lines instead of straight lines

• Verticle point values - Adjust the point values to make the desired curve.

Logical Switches are virtual two-position switches whose values (ON/OFF or +100/-100) are based on the evaluation (true/false) of a defined logical expression. Once configured, logical switches can be used anywhere in EdgeTX that a physical switch can be defined.

The Logical Switches page in Model Settings shows you all the configured logical switches as well as an overview of their configured options.

Selecting a logic switch will give you the following options:

• Edit - Opens the Logical Switches configuration page for the selected logical switch.

• Copy - Copies the selected logical switch

• Paste - Pastes a copied logical switch onto the selected logical switch. Note: it will overwrite the selected logical switch.

• Clear - Deletes all configuration options for the selected logical switch.

After selecting to edit a logical switch, you will have the following configuration options:

• V1 - The first variable in the expression to evaluate.

• V2 -The second variable in the expression to evaluate.

• AND switch - Switch that must be active to allow the logical switch to be evaluated for activation.

• Duration - The duration that the logical switch will remain active (true) once meeting activation criteria. If set to 0.0, the the logical switch will remain active (true).

• Delay - Delay between when the activation criteria for the logical switch has been met and when the logical switch changes to the activated state (true).

Logical Switch Functions

In the expression, a and b represent sources (sticks, switches, etc.), and x represents the constants (values) to be compared.

The Special Functions section of Model Setup, as the name implies, is where you can configure the special functions that are included in EdgeTX. These special functions add additional functionality beyond normal model controls such as enabling trainer mode, playing a sound, adjusting the radio backlight, adjusting radio volume, etc. On the special functions screen you will see all configured special functions as well as some of the configured options such as function name, activation switch, if the function is enabled, and other configuration options.

To add a new special function, simply select an unconfigured special function (ex: SF3 in the image above) and the special function configuration window will appear. See below for information about configuring new special functions.

Selecting an already configured special function will give you the following options:

• Edit - Opens the special function configuration page

• Copy - Copies the selected special function

• Paste - Pastes a copied special function to the selected special function. Note: this will overwrite the value of the selected special function with the copied special function.

• Insert - Inserts a blank special function above the selected special function

• Clear - Clears all configured options from the selected special function.

• Delete - Deletes the selected special function.

Configuring Special Functions

All special functions have the configuration options below. Additional options may be added based on the selected function. See the Functions section below for these additional options.

• Switch - The switch that will make the special function active.

• Function - The function that will be used. See below for function descriptions.

• Enable - Toggle on / off to enable the function. To be able to activate the special function by a switch, it must be enabled. Disabled special functions will not function regardless of the configured switch position.

Functions

Below are all the available functions in EdgeTX, what they do, as well as what other configuration options exist specifically for that function.

Override (Channel Override) - Overrides the defined channel with the defined value.

• CH - Channel to be overridden

• Value - Value to replace the normal channel value. (Range -100 to +100)

Trainer - Enables trainer mode.

• Value - Specifies which controls will be given over to the student. Options include Sticks (all sticks), Rud (Rudder), Ele (Elevator), Thr (Throttle), Ail (Aileron), and Chans (all channels).

Inst. Trim (Instant Trim)- Sets all trims to the current values of their respective sticks.

Reset (Reset Timer)- Resets the timer or telemetry specified in the value back to their initial values.

Set (Set Timer) - Sets the specified timer to the specified value.

• Timer - Options are Timer 1, Timer 2, Timer 3

• Value - The range is 00:00:00 to 08:59:59

Adjust (Adjust Global Variable) - Changes the value of the specified global variable.

• Global var - Select the global variable that you want to adjust.

• Mode - Select the mode to change the global variable. Options are: Constant, Mixer Source, Global var, Inc/Decrement

  • Constant - Sets the specified global variable to the defined constant value.

  • Mixer Source - Sets the specified global variable to the defined mixer source value.

  • Global Var - Sets the specified global variable to the defined global variable value.

  • Inc/Decrement - Increments/decrements the specified global variable by the specified amount.

Volume - Changes the radio volume. The change source is specified in the Volume dropdown.

SetFailsafe - Sets the custom failsafe values for the selected module (Internal/External) to the current stick position when activated. For this option to work, the Failsafe mode for the RF module must be set to custom.

Play Sound - Plays the sound selected in the value field when activated.

• Value - Sound to play. Possible values are Beep1/2/3, Warn1/2, Cheep, Ratata, Tick, Siren, Ring, SciFi, Robot, Chirp, Tada, Crickt, AlmClk. Note: SD card sound pack is not required.

• Repeat - Frequency to repeat the sound. Options are !1x (do not play at startup even if the switch is active), 1x (play once), 1s thru 60s (play every xx seconds).

Play Track - Plays the .wav sound file selected in the value field when activated.

• Value - .wav sound file to play from the SD card.

• Repeat - Frequency to repeat the track. Options are !1x (do not play at startup even if the switch is active), 1x (play once), 1s thru 60s (play every xx seconds).

Play Value - Announces the value of the selected element in the value field.

• Value - The source for the value to announce. It can be an input, stick, pot, slider, trim, physical and logical switch, trainer import channel value, global variable, telemetry sensor or channel.

• Repeat - Frequency to repeat the announcement. Options are !1x (do not announce at startup even if the switch is active), 1x (announce once), 1s thru 60s (announce every xx seconds).

Lua Script - Executes the Lua script defined in the value field. The Lua script must be located in /SCRIPTS/FUNCTIONS/ folder on the SD card. Lua scripts that display information on the screen cannot be executed with this special function.

BgMusic - Plays the .wav file selected in the value field on a loop when enabled. The file shall be in the SOUNDS/(language)/ folder on the SD card.

BgMusic II - Temporarily pauses the .wav file playback specified in the BgMusic

Vario - Enables the variometer beeping sound for the ascent and descent of the model.

Haptic - Causes the radio to vibrate (haptic feedback) when enabled.

• Value - Type of vibration pattern. Options are: 0 - 4.

• Repeat - Frequency to repeat the vibration pattern. Options are !1x (do not vibrate at startup even if the switch is active), 1x (vibrate once), 1s thru 60s (vibrate every xx seconds).

SD Logs - Creates a log .csv file of the radio and telemetry values in the LOGS folder on the SD Card. The radio will create a new entry into the log file based on the frequency configured in the Value setting. The value options are 0.0s - 25.5s (Note: 0.0 effectively disables this option). Each time the function is activated the radio will create a new log file provided that the function is activated at least as long as the value setting.

Backlight - Adjusts the brightness of the radio screen based on the source defined in the value dropdown.

Screenshot - Creates screenshot as a .bmp file in the SCREENSHOT folder on the SD Card.

RacingMode - Enables racing mode (low latency) for FrSky Archer RS receivers. Racing mode must also be enabled in External RF Module Settings.

No Touch - Disables the touch interface for touchscreen-enabled radios.

Set Main Screen - Changes the current visible screen to the screen number defined.

• Repeat - When the switch remains active, the repeat value determines how often the special function will change the screen to the defined screen. Options are !1x (do not change at startup even if the switch is active), 1x (change once), 1s thru 60s (change every xx seconds). This is useful because when the switch has been activated, the user can still manually switch screens, and then it will change back to the defined screen after the defined duration.

Global variables are variables whose values are shared across all the configuration screens of a model. Their values can be used in weights, offsets, differential, expo settings, outputs, and in logical switch comparisons. The Global Variables screen of Model Settings shows the value of each global variable for each flight mode.

Selecting a global variable from the global variable screen will give you the following options:

• Edit - Opens the global variable configuration screen for the selected global variable.

• Clear - Clears the global variable values for all flight modes for the selected global variable.

The global variable configuration screen is where you assign a value and other configuration options to a global variable. Additionally, you can select how the value of the global variable is defined for every flight mode - either the value is manually defined or inherited from another selected flight mode. It contains the following configuration options:

• Name - Name for the global variable. Three characters are allowed. If left blank, it will use the default GV# as the name.

• Unit - (optional) Allows you to add a % label to the displayed values when selected. It DOES NOT affect how the values are calculated.

• Precision - Allows you to select the number precision options whole numbers (0.-) and decimal (0.0). The default value is 0.-

• Min - Defines the minimum that is allowed for the global variable.

• Max - Defines the maximum value that is allowed for the global variable.

• FM0 - The value of the global variable on Flight Mode 0.

• FM1 -> FM8 - When the toggle switch is enabled or disabled, the following applies:

  • Toggle switch disabled - global variable value for the selected flight mode is inherited from the flight mode defined in the drop-down.

  • Toggle switch enabled (highlighted) - the global variable value for the selected flight mode is manually defined in the text field.

The Radio Settings section contains all the options to configure your radio. Across the top of the page you will see icons that will take you to different pages of radio settings when selected. The default screen for the radio settings is the screen.

Icons at the top of the radio settings screen include (in order from left to right):

The below options can be configured for sensors:

• Name: Name of the sensor - up to 4 characters.

• Type: Options are custom or calculated. Custom sensors are defined by the hardware. Calculated sensors are a sensors whose value is calculated using other sensors values. See below for more information on calculated sensors.

• ID: This number indicates what type of sensore it is. It contains two parts. The first part is the ID number which defines the sensor type. The second part is the instance number for the hardware. If multiple sensors of the same type are configures, the instance numbers must be unique.

• Unit: The unit for the sensor. This unit is used when the sensor value is displayed on the screen or read aloud.

• Precison: Specifies the number of digits after the decimal point when the sensor value is displayed on the screen. The number is truncated based on this setting.

• Ratio: Specifies the ratio value to multiply with the sensor value as needed by some sensors.

• Offset: Specifies the offset value to add to the sensor value.

• Auto Offset: When selected, the first received value is used as offset. You can use the option to reset the offset on already configured sensors.

• Positive: When selected, the value of the sensor will be displayed only when it is a positive number. Displays zero when the sensor value becomes a negative number.

• Filter: When selected, the sensor value becomes a rolling average of the last 5 received values.

• Logs: When selected, the value of this sensor will be saved in the log file. SD Card logging is configured in or Global Functions.

Calculated sensors contain the additional configuration options:

• Formula: Type of calculation to use. Options include:

  • Add: Add the values of up to 4 designated sensors.

  • Average: Calculates the average value of up to four designated sensors.

  • Minimum: Find the minimum value of up to 4 designated sensors.

  • Maximum: Find the maximum value of up to 4 designated sensors.

  • Multiply: Multiplies the value of 2 sensors.

  • Totalize: Calculate the cumulative value of one sensor.

  • Cell: This is the formula for FrSKY Lipo battery sensor. It displays cell voltage specified by the number in "Cell index" field. If you specify "Lowest" in "Cell index" field, the voltage of the cell with the lowest is displayed. If you specify "Highest" in "Cell index" field, the voltage of the cell with the highest is displayed. If you specify "Delta" in "Cell index" field, the voltage difference between lowest and highest cell is displayed

  • Consumpt: Calculates the power consumption (mAh) by cumulatively add the values of current sensor.

  • Distance: Calculates the distance between the receiver and the radio using GPS sensor and altimeter values.

• Source 1, 2, 3, 4: The sensors that will provide the argument values that are used in the formula defined above.

• Persistent: When selected the sensor values will be saved when switching between models or powering down the radio.

Telemetry is data received from the model to the radio from various sensors. These sensors may be in included in the radio receiver or flight controller, or may be separate sensors, such as GPS, variometer, or magnetometer. Telemetry data that is received can be displayed by EdgeTX in widgets, configured in alarms or audio call-outs.

RSSI

RSSI stands for the Receiver Signal Strength Indicator and represents the raw strength of the received signal. How the RSSI value is determined is based on the protocol being used, but generally the higher the number the better, with 100 being the maximum value.

• Low alarm - The threshhold value when the "RF signal low" voice prompt will be played. The recommended value is 45.

• Critical alarm - The threshhold value when the "RF signal critical" voice prompt will be played. The recommended value is 42.

• Disable telemetry alarms - When enabled, no alarm voice prompts will be played.

Sensors

All prevously configured sensors are listed here. Sensors that are highlighted have received data since the model was loaded or the telemetry values were reset. A small circle icon will flash to the left of the sensor value when it has received a data update. Sensor values in black designate the sensors that are receiving regular updates. Sensor values that are red are no longer receiving regular updates. See Recognized Sensors for a list of commonly used sensors in EdgeTX.

The following options are listed under the sensor list.

• Discover New: When selected, it will look for new sensors on the model and automatically configure them.

• Add New: When selected, it will create a new blank sensor for that must be configured manually.

• Delete All: This option will delete all prevously configured sensors.

• Ignore Instances: This options prevents mutltiple sensors from reporting the same telemetry data.

If you select a specific sensor, you will get the following options:

• Edit: Allows you to edit the sensor's configuration options.

• Copy: Creates a copy of that sensor.

• Delete: Deletes that sensor.

See the Sensor Configuration Options page for detailed description of all the configuration options for setting-up or editing sensors.

Variometer

A variometer detects changes in the model altitude. EdgeTX can alert the user of these altitude changes by providing a rising/lower pitched tone. Use the Variometer menu on the Radio Setup page to set the actual frequency and volume of the tone to be played. The following options exist to configure the variometer alarm.

• Source - Specifies the sensor to use as the variometer. It is selected from the telemetry sensors added in Sensors section.

• Range - Specifies the ascent/descent range that will trigger the change in the Variometer beeping pitch. If climb/descent rate is within the range specified here, beeping pitch will change according to that value. When it goes beyond the range specified here, beeping pitch will stop changing. Units are meters/second or feet/second based on the Units setting on the Radio Setup page.

• Center - Specify the range for ignoring changes in climb/descent rates. When the climb/descent rate is within the range specified here, the beeping pitch will not change.

• Tone/Silent - Specifies whether to beep when climb/descent rate is within the range specified by Center.

The SD Card screen shows you the contents of your SD card, allows you to navigate the folders and interact with the files in the folders. All folders contain a README.txt file that describes what type of files belong in this folder. After selecting a file in one of the folders, you will be presented with some of the options below, depending on the file type that was selected:

• Assign bitmap - Assigns the selected image file as the model image of the currently selected model.

• Copy - Copies the selected file.

• Delete - Deletes the selected file.

• Execute - Executes a Lua script. Used for files ending in .lua

• Flash [target]- Flashes the selected firmware file to the select target module. Examples: Flash Bootloader, Flast Internal Multi.

• Paste - Pastes the copied file.

• Play - Plays the selected sound file.

• Rename - Renames the file.

• View text - Views the selected .txt or .csv file.

The folders listed on the SD card screen are the same as what you will see when connecting your radio to your computer. Below are the folder names and explanations for all the folders that come with the default EdgeTX SD Card.

FIRMWARE

Place the firmware files that you want to flash in this folder. This folder is empty by default (except for the readme.txt file). When selecting a .bin file you will be given the option to flash the firmware to a particular module. Also, only firmware files in this location will be visible from the bootloader menu.

IMAGES

Place your custom model or splash screen image files in this folder. This folder is empty by default (except for the readme.txt file). Selecting an image file will give you the option to Assign Bitmap, which assigns the selected image file as the model image of the currently selected model.

The ideal image size for model images is 192x114 pixels. The picture format should be .png. The image file name should not exceed 9 characters.

The ideal image size for Splash Screen images is the actual radio screen size (480x272 pixels for most color screen radios). The picture format should be .png. The image file name must be splash.png. Screen dimensions for the supported color screen radios can be found here.

LOGS

This is where the log files that are configured in the special function SD Logs are written. These files can be viewed with the View text option. This folder is empty by default (except for the readme.txt file).

MODELS

This is where the model files, label information, and preflight checklists are stored. Each model will have a model[#].yml file that contains all configured options. Additionally, there is a labels.yml file that contains all the label information for your models.

Models that are deleted via the radio will be moved to the DELETED folder that is included in this folder. The remaining model files are what will be visible on the Model Select screen.

If you have configured the Display checklist option in model settings, the model notes file goes in this folder. The model notes file must be a .txt file and must have the EXACT same name as the model it is for, for example: Mobula6.txt. The text in the file is up to the user.

RADIO

This folder contains the radio.yml file. This file contains all the radio configuration data. If this file is corrupted or missing, the radio will go into Emergency Mode and will create a new radio.yml file with the default settings.

SCREENSHOTS

This is where the screenshot image files that are configured in the special function Screenshot are written. This folder is empty by default (except for the readme.txt file).

SCRIPTS

This folder and its subfolders are where the Lua scripts get placed. It contains the following sub-folders by default. You can download additional Lua scripts from https://github.com/EdgeTX/lua-scripts.

• Functions - This folder is where the functions Lua scripts that can be activated by the special function Lua Script must be placed. This folder is empty by default (except for the readme.txt file). More information about function Lua scripts can be found here: Function Scripts.

• Mixes - This folder is where the Lua mixer scripts shall be placed. This folder is empty by default (except for the readme.txt file). More information about Mixer Lua scripts can be found here: Custom Mixer Scripts

• Tools - Contains the Lua scripts that are available in the Tools screen.

• Wizards - Contains the Wizard Lua scripts that are available in the Tools screen.

SOUNDS

This folder is where the EdgeTX sound packs for your radio get placed. The sound packs are language-specific and correlate to the Voice language option in Radio Setup. Selecting a sound file from this folder will give you the option Play, which plays the selected sound file.

Sound packs are available for manual download at: https://github.com/EdgeTX/edgetx-sdcard-sounds/releases. It is also possible to create custom sounds to use in EdgeTX. For your custom sounds to be playable by EdgeTX ensure that they meet the following criteria:

• File Name: 123456.wav (up to 6 characters plus .wav)

• Sample Rate: 32 kHz (or 16 Khz, 8Khz)

• Bits / Sample: 16 (or 8)

• Tracks: 1, mono

• Compression Codec: PCM

TEMPLATES

This is where model template files are stored. By default, it will have the following sub-folders:

• PERSONAL - If you save your models as templates, then they get stored here.

• SoarETX - A collection of sailplane templates by: Jesper Frickmann

• Wizard - Simple model templates that use the Lua Wizard scripts to configure the models.

THEMES

This folder contains the theme packs for EdgeTX. The EdgeTX SD card comes with several theme packs automatically installed.

You can download and add additional themes from: https://github.com/EdgeTX/themes.

WIDGETS

This is where the widget files are stored. You can add additional widgets to this folder to use with EdgeTX. For more information about the widgets that are pre-installed with EdgeTX, see Widgets. You can download additional widgets from https://github.com/EdgeTX/lua-scripts.

The Tools page in Radio Settings is where you can select Lua script-based tools for execution. Lua scripts that are located on the SD card in the Tools folder will be listed here. Selecting a tool will execute it in full-screen mode. By default, EdgeTX includes several tools. Other tools can be downloaded and added to the SD card as well. The following tools are included in the default EdgeTX SD card.

Model Locator (by RSSI)

The Model Locator tool helps to find a lost model based on the RSSI (if still available). The widget produces an audio representation (variometer style) of the RSSI from the lost model. The widget will also display the RSSI in a visible colorized bar (0-100%).

Spectrum (INT)

The Spectrum Analyzer tool will show the strength of signals in the 2.4GHz band. It uses the internal MULTI-Module as a 2.4GHz spectrum analyzer.

The display shows frequencies on the 2.4GHz spectrum, from 2400MHz to 2480MHz. The X (horizontal) axis shows the frequency in MHz and the Y (vertical) axis shows relative signal strength.

T: Frequency at the center of the plot (fixed at 2440MHz) S: Bandwidth of the plot (fixed at 80MHz) T: Position of the cursor (vertical line)

Pressing ENT and scrolling left and right allows the T value to be changed, which will move the vertical line to highlight a specific frequency.

Wizard Loader

The Wizard Loader tool assists you in setting up a new model by running a setup wizard for a particular model type. Once the model type is selected, the wizard will take you through a series of prompts and then configure your selected model based on the information provided.

NOTE: The wizard does not create a new model, it only configures the currently selected model. You must manually create a new model first and then run the wizard. If you run this wizard on an already configured model, it will overwrite your model settings!

Selecting one of the 6 buttons on the Radio Setup screen will take you to one of the additional setting screens below.

Many of the additional settings here are self-explanatory. Only those settings needing clarification will be mentioned below.

Sound

Mode - configures when to play sounds.

• All - Beeps when the buttons are pressed and sounds are played when there are alerts or warnings.

• No Key - No beeps when buttons are pressed or the scroll wheel is turned but does play sounds when there are alerts or warnings. Also plays sounds triggered by special functions.

• Alarm - Only plays alarm or warning sounds. Also plays sounds triggered by special functions.

• Quiet - No Beeps or sounds are played.

Volume

The master volume for the radio.

Wav volume

The volume for alerts and warnings and sounds that are played with the Play track special function

Background volume

The volume for background .wav files (music) that are played with the BGMusic special function

Variometer

Repeat Zero

The time before the tone repeats in milliseconds.

Haptic

Mode - configures when the radio vibrates.

• All - Vibrates when the buttons are pressed and when there are alerts or warnings.

• No Key - No vibrations when buttons are the pressed or scroll wheel is turned but does vibrate when there are alerts or warnings.

• Alarm - Only vibrates for alarms or warning sounds.

• Quiet - No vibrations are made.

Alarms

Sound Off

An "alarms disabled" visual warning is displayed when the transmitter is turned on if the sound mode is set to quiet.

Check RSSI on Shutdown

Checks if a receiver is still connected to the radio on attempted shutdown. Makes a audio and visual alert if one is detected.

Backlight

Mode

• Off – Always off.

• Keys – Turns on when buttons are pressed.

• Ctrl – Turns on when sticks, switches, and knobs are used.

• Both – Turns on when buttons, sticks, switches, and knobs are used.

• ON – Always on.

Time

The length in seconds that the backlight is on. The minimum value is 5 seconds. The maximum value is 600 seconds.

Alarm

The backlight turns on when there are alarms or warnings.

GPS

Coordinate Format

The GPS coordinate format that will be displayed.

Adjust RTC

Adjust the transmitter's real-time clock to match the time determined by the GPS.

The Theme screen allows you to apply different colored themes to your radio. By default, the EdgeTX SD card comes with the themes shown above. Long pressing on a selected theme will give you the following options:

• Set Active - Sets the selected theme as the active theme.

• Edit - Opens the theme editor to edit the selected theme.

• Duplicate - Makes a copy of the selected theme.

• Delete - Deletes the selected theme.

To edit a theme in the Theme Editor, select the color variable from the list on the left side of the screen. Once you do, the Edit Color screen will be shown.

Select the color using either the color scales on the left side of the screen. You can choose between the RGB and HSV color scales with the buttons at the upper right side of the screen.

Once you have your desired color, press the theme logo in the upper left corner to go back to the Edit Theme screen to select another color variable to edit. Once you are finished, press the theme logo to exit the Theme Editor and save your changes.

The Radio Setup screen is where you configure basic settings for your radio. It contains the following options:

Date - The current date. This date is used for the SD card log files.

Time - The current time. This time is used for the SD card log files.

Pwr Off delay - The delay between when the power button is pushed and when the radio shuts off. The options are: 0s, 1s, 2s, 3s, 4s. It is recommended to set at least a 1s delay in order to prevent the radio from being shut off in the case of an accidental button press.

Owner ID - Custom registration ID used only for users with ISRM modules.

Country code - Used by some RF modules to ensure adherence to local regulatory RF requirements. Options are America, Japan, Europe.

Voice language - Language for the voice pack. This setting and the voice pack folder on the SD card must match for the sounds to be played.

Units - Units of measure. Options are metric or imperial.

Play delay (sw. mid pos) - The minimum time in milliseconds a switch must be in the middle position before a special function will get activated. This is used to prevent the middle position from being activated on a three-position switch when switching from low position to high position.

USB Mode - Sets the default action when a USB cable is plugged into the USB data port and the radio is powered on. Options are: Ask, Joystick, Storage, and Serial.

Rotary Encoder Mode - Set to Normal by default. The Inverted option reverses the direction of the roller.

Default Channel Order - The default channel order for new models and the trainer screen. The letters stand for: A = Aileron, E = Elevator, T = Throttle, R = Rudder. Changing this setting does not affect existing models.

Mode - The stick mode that will be used for the transmitter. Defined by what actions the left stick takes. The options are:

• 1: Left = yaw+pit (pitch)

• 2: Left = yaw+thr (throttle)

• 3: Left = rol (roll)+pit (pitch)

• 4: Left = rol (roll)+thr (throttle)

Model quick select - Affects model selection screen. Both options require you first to mark the desired model using the scroll wheel or short tap.

• When OFF: short/long tap (short/long ENTER) on the marked model will show the menu, where you can "Select model";

• When ON: short tap (short ENTER) on the marked model will select it immediately. To activate the menu, make a long tap or long ENTER.

The Version screen displays information about the current EdgeTX version that is being used:

• FW - Firmware name

• VERS - Firmware version

• DATE - Date firmware was compiled

• TIME - Time firmware was compiled

• OPTS - Build options that were enabled when compiled.

The Modules / RX Version gives you information about the activated RX modules for the currently selected model.

The following sensors are commonly used and normal automatically detected by EdgeTX:

The Hardware screen is where you configure hardware specific-settings for your radio. It contains the following configuration options:

Battery meter range - Sets the maximum and minimum voltage for the battery meter. This should be set based on the type of battery you are using.

Battery Calibration - Set this value to match the transmitter battery voltage.

Check RTC voltage - When enabled, checks the RTC battery at startup and warns you if the battery voltage is low.

ADC Filter - Enables or disables the ADC Filter. This filter can also be enabled/disabled per model in the model settings.

External RF Sample Mode - Options are Normal and OneBit. The default setting of Normal should be used by most users. Only users of X9D+ and X7 radios may want to use OneBit mode.

Serial Port - Displays a list of available auxiliary serial ports that can be configured and used. The listed ports are based on the ports that are available in the particular radio hardware. The ports listed below are for example only and may not be present in your radio.

• AUX1 - First available auxiliary serial port can be configured with the below options:

  • OFF - Turned off.

  • Telem Mirror - The same telemetry data that goes to the external module bay is sent to the serial port.

  • Telemetry In - Receive telemetry data over the serial port.

  • SBUS Trainer - Connect the Instructor and Student radios over the serial port.

  • LUA - Send/receive data to/from Lua script.

  • GPS - Receive GPS telemetry data over the serial port.

  • CLI - Send commands to the radio via the command line.

• Port Power - Enables or disables the power output on the power supply pins next to serial ports that are available on some radios (presently only TX16S has this feature).

Calibration - For calibrating your physical radio controls (sticks, pots, sliders, & 6-position switch). The radio will prompt you through the calibration steps.

Inputs, Sticks, Pots, and Switches Buttons

Selecting one of the Inputs, Sticks, Pots, or Switches Buttons will open the configuration screen. On this screen, you will see all the physical radio controls pre-defined by EdgeTX. Here you can add a 3 character label to the control as well as change the type of control as needed.

Debug

The debug section allows for testing and debugging of the analog controls and keys.

Debug Analogs - These screens will show you the data for your analog controls (Sticks, Sliders, Pots, 6-position switch) and the touch screen on your radio. There are three views - Calibrated analog, Filtered Raw Analog with deviation, Unfiltered raw analog, and Min Max and range.

Debug Keys - This screen will show you the digital data for your keys, switches, trims, and the rotary encoder (roller).

The Trainer screen in Radio Settings is used to configure how the radio in Master mode will handle the signals from the radio in Slave mode.

For each of the four main control inputs (Ail, Ele, Thr, Rud), the following options can be configured (for each row, from left to right).

• Mode - How the instructor’s radio will handles the signals from the student's radio

  • OFF - Stick values from the radio in Master mode will be used - no input from the radio in Slave mode.

  • += Adds the stick values from both the radios in Master and Slave modes.

  • := Replaces the stick values from the radio in Master mode with the stick values from the radio in Slave mode. (Default)

• Source channel - The channel from the radio in Slave mode that is mapped the control input.

• Weight - Percentage of stick travel to use of the radio in Slave mode. Use negative values to change the stick direction.

• Cal (calibrate)- Sets the center stick value of the radio in Slave mode.

• Multiplier - This value changes the weight of all the sticks together.

Global functions are special functions that apply to all models on the Radio. They are configured exactly as model Special Functions and the same functions are available. For more information about configuring Global Functions, refer to the section as they are essentially the same.

Reset flight - When selected, this option:

• Resets all timers configured with a persistence setting of Flight to zero.

• Resets all discovered telemetry sensor values.

• Resets all logical switch states

• Triggers the same checks as loading the model - i.e. throttle position, switch state, is failsafe set check, display pre-flight checklist if configured, stuck keys test, etc.

Reset timer 1 / 2 / 3 - Resets only the selected timer to zero regardles of the configured persistence setting.

Reset telemetry - This option resets all discovered telemetry sensor values.

Below are descriptions and configuration options for widgets included with EdgeTX.

Value - displays a numeric value of the defined source as text. The configurable options are:

• Source - source for the text to be displayed

• Color - Opens the color picker to choose the color for the text. User can choose between RGB and HSV color model to choose the color.

• Shadow - When enabled, adds a shadow to the text.

Timer - Displays the selected timer. No configurable options other than timer selection.

Text - Displays a user-customizable text field. The configurable options are:

• Text - Text to display

• Color - Opens the color picker to choose the color for the text.

• Size - Size for the text. Options are STD (Default), BOLD, XXS, XS, L, XL, XXL

• Shadow - When enabled, adds a shadow to the text.

Outputs - Shows the channel output values in a bar graph. The number of channels that are displayed is dependent on the size of the widget. The configurable options are:

• First channel - selects the first channel to display in the widget.

• Fill background - Adds a solid background color to the widget when enabled

• BG Color - Opens the color picker to choose the color for the background.

• Text Color - Opens the color picker to choose the color for the text.

• Color - Opens the color picker to choose the color for the output bars.

Model info - Displays the selected model name and picture (if configured in model settings). The configurable options are:

• Color - Opens the color picker to choose the color for the name text.

• Size - Size for the name text. Options are STD (Default), BOLD, XXS, XS, L, XL, XXL

• Fill background? - Adds a solid background color to the widget when enabled

• BG Color - Opens the color picker to choose the color for the background.

• Use Theme Color - When enabled, overrides the text color with the text color of the configured theme.

Gauge - Shows a bar graph for the source value. The configurable options are:

• Source - Source for the gauge.

• Min - Minimum value for the gauge. This value will be 0%

• Max - Maximum value for the gauge. This value will be 100%

• Color - Opens the color picker to choose the color for the gauge text and bar.

BattAnalog - Displays a graphical representation of the charge level of a Lipo/Li-ion. It will automatically detect the cell count of the battery. It works with telemetry where only the total battery voltage is received. The configurable options are:

• Sensor - Sensor for the battery voltage to use.

• Color - Opens the color picker to choose the color for the text.

• Show_Total_Voltage - Shows total battery voltage (instead of calculated cell voltage) when enabled.

• Lithium_Ion - Adjusts the minumum battery voltage used in calculating the remaining battery percentage from 3.0 to 2.8 when enabled.

BattCheck - Displays a graphical representation of the charge level of a Lipo/Li-ion. It works with telemetry where individual cell voltage is received, such as FLVSS liPo Voltage Sensor. The configurable options are:

• Sensor - Sensor for the battery voltage to use.

• Color - Opens the color picker to choose the color for the text.

• Shadow - When enabled, adds a shadow to the text.

• LowestCell - When enabled, shows only the voltage of the lowest cell (vs. showing all cell voltages).

• Lithium_Ion - Adjusts the minimum battery voltage used in calculating the remaining battery percentage from 3.0 to 2.8 when enabled.

Counter - It incrementally counts. The configurable options are:

• Color - Opens the color picker to choose the color for the text.

• Shadow - When enabled, adds a shadow to the text.

Event Demo - Demonstrates handling of key and touch events in full screen mode. For demo purposed only. The configurable options are:

• Size - Changes the size of the box in full screen mode.

Flights - Counts your number of flights. The configurable options are:

• switch - Designated Arm/Safe switch.

• motor_channel - Channel for the motor.

• min_flight_duration - Minimum flight duration for the flight to be counted.

• text_color - Opens the color picker to choose the color for the text.

• debug - When enabled, shows status information on the widget.

Additional notes regarding this widget:

The flight is considered successful if after 30sec the engine is above 25%, telemetry is active (to indicated that the model connected), and safe switch ON. The flight is considered ended after 8 seconds of battery disconnection (detected by no telemetry) -- warning: do NOT use this widget if model is using GV9!!!

The widget assumes the following: the model has a motor, the motor is activated on channel 3 (can be configured in settings), there is telemetry with one of the above [RSSI|RxBt|A1|A2|1RSS|2RSS|RQly], there is a safe switch (arm switch), and global variable GV9 is free (i.e. not used).

Gauge Rotary - a configurable analog style gauge with a needle. Also shows the minimum and maximum values that were read by the gauge with green and red needles. The configurable options are:

• Source - Source for the gauge.

• Min - The minimum (lowest) gauge value.

• Max - The maximum (highest) gauge value.

• HighasGreen - Enable for a sensor where high values are good. Disable for sensor where low values are good.

• Precision - The precision of the number value to display in decimals.

Ghost- The Ghost widget will display RF receiver or video transmitter telemetry data based on the mode that is configured.

In normal mode, the widget provides RF Mode (RFMD), Frame Rate (FRATE), Link Quality (RQLY), and Transmit Power (TPWR)

In video mode, the widget provides Video Band (VBAN), Video Frequency (VFRQ), Video channel (VCHAN), and Video Power (VPWR)

LibGUI Demo - This widget is a demo for the LibGUI library. This library is not normally run by itself. Instead, it provides interactive functions to other Lua scripts that use it. The widget must be run in full-screen mode to demo the library's functionality.

SOARETX - The EdgeTX version of the SoarOTX tool. It is a package of sailplane models for EdgeTX transmitters. It provides Lua scripts for timing and scorekeeping, graphing of log data (e.g. altitude graphs), and model configuration.

Timer2 - Displays the selected timer with the timer text scaled based on the select widget size and has the following configuration options:

• TextColor - Opens the color picker to choose the color for the text.

• Timer - Timer to display.

• use_days - Shows days when the time value is over 24 hours when enabled.

TxGPStest - Displays GPS Information in text format. There are no configurable options.

The Statistics screen presents you with statistics regarding radio usage. Except for Battery, all data is reset once the radio is powered off. The following information is provided:

• Session - The amount of time that the radio has been turned on.

• Battery - The amount of time that the radio has been on since the last reset.

• Throttle - The amount of time that the throttle has was above the 0% stick position.

• Throttle % - The amount of time that the throttle has was above the 50% stick position.

• Timer - The current values of Timer 1, Timer 2, Timer 3.

The debug screen provides data points used by the developers when debugging issues in the software. Most users will not find the information useful on this screen unless debugging issues with developers. The following debug information is provided.

• TMix max - Maximum mixer task duration.

• Free mem - Current free radio memory in bytes.

• Lua scripts

  • [Dur] - Maximum Lua duration in milliseconds.

  • [Int] - Maximum Lua interval in milliseconds.

  • [S] - Memory used by LUA scripts.

  • [W] - Memory used by LUA widgets.

  • [B] - Memory used by LUA bitmap functions.

• Free stack

  • [Menu] - Minimum free stack memory for menu tasks.

  • [Mix] - Minimum free stack memory for mixer tasks.

  • [Audio] - Minimum free stack memory for audio tasks.

The Channel Monitor shows both the output value (top bar) and mix value (bottom bar) for each of the 32 radio channels, spread across 4 pages of 8.

The 5th page of the channel monitor is the logical switches monitor. On this page, you will see the status (activated/non-activated) of all logical switches. Logical switches that are activated are highlighted.

The Screen settings section of EdgeTX is where you can customize your main views and add additional views. When selecting Screen Settings from the main navigation menu it will open Main view 1. If other main views have been added, you may select them from the number tab at the top of the screen to adjust their settings. All main view tabs have the following configuration options and are configured individually:

• Layout - Selects the screen layout for the widgets. It is possible to divide the screen in up to two columns and up to 4 rows, with a widget in each cell.

• Setup Widgets - see Setting up widgets below.

• Top bar - Toggles whether the top widget bar will be visible on the selected main view.

• Flight mode - Toggles whether the flight mode name (if configured) will be visible on the selected main view.

• Sliders - Toggles whether the slider bars will be visible on the selected main view.

• Trims - Toggles whether the trim bars will be visible on the selected main view.

• Mirror - Toggles whether to mirror the selected widget layout.

Selecting the user Interface button to the left of the Main view 1 tab will open the user interface configuration screen. It contains the following options:

• Top bar Setup Widgets button - Sets up the widgets that will be displayed on the top bar. See Setting up widgets below for information on how to setup widgets.

• Theme - Applies the selected theme to EdgeTX. A preview of the theme is below the dropdown. EdgeTX comes with several themes installed. Additional themes to download as well as instructions for creating your own themes can be found here: https://github.com/EdgeTX/themes

Setting up widgets

Selecting the setup widgets button will display the main view or top bar with the widget cells outlined in a hashed line. You can assign a widget to a cell by selecting the cell and then the widget you want to assign to it from the drop-down menu. After selecting the widget, it will then open the configuration options for the widget for further configuration. Widget descriptions and configuration options for widgets included with EdgeTX are below.